For the Gluster to communicate within a cluster either the firewalls have to be turned off or enable communication for each server.
# iptables -I INPUT -p all -s `<ip-address>` -j ACCEPT
Configure the trusted pool
Remember that the trusted pool is the term used to define a cluster of
nodes in Gluster. Choose a server to be your “primary” server. This is
just to keep things simple, you will generally want to run all commands
from this tutorial. Keep in mind, running many Gluster specific commands
gluster volume create) on one server in the cluster will
execute the same command on all other servers.
nodename with hostname of the other server in the cluster,
or IP address if you don’t have DNS or
Let say we want to connect to
# gluster peer probe node02
Notice that running
gluster peer status from the second node shows
that the first node has already been added.
Partition the disk
Assuming you have a empty disk at
# fdisk /dev/sdb
And then create a single XFS partition using fdisk
Format the partition
# mkfs.xfs -i size=512 /dev/sdb1
Add an entry to /etc/fstab
# echo "/dev/sdb1 /export/sdb1 xfs defaults 0 0" >> /etc/fstab
Mount the partition as a Gluster "brick"
# mkdir -p /export/sdb1 && mount -a && mkdir -p /export/sdb1/brick
Set up a Gluster volume
The most basic Gluster volume type is a “Distribute only” volume (also referred to as a “pure DHT” volume if you want to impress the folks at the water cooler). This type of volume simply distributes the data evenly across the available bricks in a volume. So, if I write 100 files, on average, fifty will end up on one server, and fifty will end up on another. This is faster than a “replicated” volume, but isn’t as popular since it doesn’t give you two of the most sought after features of Gluster — multiple copies of the data, and automatic failover if something goes wrong.
To set up a replicated volume:
# gluster volume create gv0 replica 3 node01.mydomain.net:/export/sdb1/brick \ node02.mydomain.net:/export/sdb1/brick \ node03.mydomain.net:/export/sdb1/brick
Breaking this down into pieces:
- the first part says to create a gluster volume named gv0
(the name is arbitrary,
gv0was chosen simply because it’s less typing than
- make the volume a replica volume
- keep a copy of the data on at least 2 bricks at any given time. Since we only have two bricks total, this means each server will house a copy of the data.
- we specify which nodes to use, and which bricks on those nodes. The order here is important when you have more bricks.
It is possible (as of the most current release as of this writing, Gluster 3.3) to specify the bricks in such a way that you would make both copies of the data reside on a single node. This would make for an embarrassing explanation to your boss when your bulletproof, completely redundant, always on super cluster comes to a grinding halt when a single point of failure occurs.
Now, we can check to make sure things are working as expected:
# gluster volume info
And you should see results similar to the following:
Volume Name: gv0 Type: Replicate Volume ID: 8bc3e96b-a1b6-457d-8f7a-a91d1d4dc019 Status: Created Number of Bricks: 1 x 2 = 2 Transport-type: tcp Bricks: Brick1: node01.yourdomain.net:/export/sdb1/brick Brick2: node02.yourdomain.net:/export/sdb1/brick
This shows us essentially what we just specified during the volume
creation. The one this to mention is the
Status. A status of
means that the volume has been created, but hasn’t yet been started,
which would cause any attempt to mount the volume fail.
Now, we should start the volume.
# gluster volume start gv0
Find all documentation here